[New post] Special cartridges with heat-shrink tubing for dymo and brother label writers

jpluimers posted: "Labeling cables is important, especially when you have a lot of them, and it is tough: Paper and plastic tables tend to loosen over time. Numbers or letters you can snap on only work on thicker cables and over time tend to break loose (due to pl" The Wiert Corner - irregular stream of stuff Special cartridges with heat-shrink tubing for dymo and brother label writers jpluimers Apr 26 Labeling cables is important, especially when you have a lot of them, and it is tough: Paper and plastic tables tend to loosen over time. Numbers or letters you can snap on only work on thicker cables and over time tend to break loose (due to plasticisers evaporating). Permanent markers are less permanent and fade over time. Hopefully heat-shrink tubing you can print on with either Dymo or Brother laber writers will outlast 3. At least they won't loosen like 2. and 1. So I was glad that [Archive] Jilles (@jilles_com) / Twitter started a thread, which I tried to help keeping coherent. Some of the messages: [Archive] Jilles on Twitter: "When you are chaotic and don't want to mess stuff up https://t.co/Wpv8dzKBQL" / Twitter Dymo [Archive] stacksmashing on Twitter: "@jilles_com At the risk of contributing to your filled mailbox: Do you know that there's Dymo Heat-Shrink-Tubing? " / Twitter [Archive] Bruce Barnett on Twitter: "@ghidraninja @jilles_com "Compatible with DYMO Rhino 4200, 5200, 6000 industrial label printers." But Robert Darby's review says it works on the $20 model 160 as well!! I'm in!" / Twitter [Wayback/Archive] Works great with the cheaper printers too! On a whim I ordered the DYMO LabelManager 160 label maker (well under $20) on the off chance that since the label reels are identical between the vinyl labels that it uses and this shrink wrap that maybe, just maybe it'll work. Not to mention, save me at least $60. As it turns out , IT DOES WORK ! [Archive/ Jilles on Twitter: "@grymoire @ghidraninja I own a Dymo LabelManager 220P and according to  the shrinktube is D1 and compatible with my label writer. Will see if that's true tomorrow. " / Twitter [Archive] Bruce Barnett on Twitter: "@jpluimers @bencpye @ghidraninja @jilles_com ..." / Twitter [Archive] Bruce Barnett on Twitter: "@jpluimers @bencpye @ghidraninja @jilles_com And the Amazon link is here ..." / Twitter [Wayback/Archive] Amazon.com: DYMO Industrial Heat Shrink Tubes for DYMO LabelWriter and Industrial Label Makers, Black on White, 3/8", (18053) : Industrial & Scientific [Archive] Jeroen Wiert Pluimers on Twitter: "@grymoire @bencpye @ghidraninja @jilles_com Jilles already got it in the mail. Awesome! ..." / Twitter [Archive] Jilles on Twitter: "Seems Nineleaf is selling DYMO compatible printable heat shrink tubes for way less: 1805443 24mm 18057 19mm = 3/4" 18055 12mm = 1/2" 18053 9mm = 3/8" 18051 6mm = 1/4" ..." / Twitter [Archive] Bruce Barnett on Twitter: "@jilles_com @jpluimers @bencpye @ghidraninja Here's the US amazon link for the 1/2" tape (18055/18056) from Nineleaf. 1 DYMO costs $34, while 3 Nineleaf cartridges costs $15. Much cheaper! No reviews though... ..." / Twitter [Archive/Archive] Amazon.com: Nineleaf 3 Pack Compatible for DYMO 18056 Rhino Heat Shrink Tube Industry Label Tape 12mm 1/2" x 5ft Black on Yellow Wire Tapes for Industrial Rhino Pro 3000 4200 5000 5200 6000 3M Label Maker : Electronics [Archive] Jeroen Wiert Pluimers on Twitter: "@jilles_com @grymoire @bencpye @ghidraninja And more posts like this (: ..." / Twitter [Archive] Jilles on Twitter: "Before and After ..." / Twitter [Archive] Jilles on Twitter: "/mail heat shrink tube for DYMO Labelwriter " / Twitter From left to right: 6mm(1/4"), 9mm(3/8"), 12mm(1/2"), 18mm(3/4"), 24mm(1"), each length 1.5m (5'). [Archive] Jilles on Twitter: "Well, 24 and 19mm don't fit in the device. ..." / Twitter [Archive] Jilles on Twitter: "6, 9 and 12mm do fit (and print) ..." / Twitter [Archive] Jilles on Twitter: "Different sizes https://t.co/UNev0vzw66" / Twitter From left to right: 6mm(1/4"), 9mm(3/8"), 12mm(1/2"), 18mm(3/4"), 24mm(1"), each length 1.5m (5'). Brother [Archive] Ben Pye on Twitter: "@jpluimers @grymoire @ghidraninja @jilles_com Brother apparently have something the same too - and again can work with their cheap printers " / Twitter [Wayback/Archive] Print Your Own Heat Shrink Labels For Factory-Chic Wire Naming | Hackaday [Archive] Ben Pye on Twitter: "@jpluimers @grymoire @ghidraninja @jilles_com Well I could have gone cheaper but PC connected was too tempting - ... Now to wait for the clone heat shrink from AliExpress…" / Twitter [Archive/Archive] Brother R700TZE231BUND Refurbished PTP700 P-touch PC-Connectable Label Printer and TZE231 Laminated Black on White TZe Tape Bundle [Archive] Ben Pye on Twitter: "@jpluimers @grymoire @ghidraninja @jilles_com There's even a protocol manual! ... If every printer had one of these the world would be a better place." / Twitter [Wayback] cv_pth500p700e500_eng_raster_110.pdf   --jeroen Continue reading Special cartridges with heat-shrink tubing for dymo and brother label writers Comment Like You can also reply to this email to leave a comment. Unsubscribe to no longer receive posts from The Wiert Corner - irregular stream of stuff. Change your email settings at manage subscriptions. Trouble clicking? Copy and paste this URL into your browser: http://wiert.me/2023/04/26/special-cartridges-with-heat-shrink-tubing-for-dymo-and-brother-label-writers/

Get the Jetpack app to use Reader anywhere, anytime Follow your favorite sites, save posts to read later, and get real-time notifications for likes and comments. Learn how to build your website with our video tutorials on YouTube. Automattic, Inc. - 60 29th St. #343, San Francisco, CA 94110